Vapoursynth LSFmod
LSFmod (LimitedSharpenFaster mod) is a strong edge and detail sharpener that keeps halos, aliasing and small "confetti" artifacts in check by limiting the result to the local minimum and maximum.
Filtering → Vapoursynth → Sharpen

What it does
The picture is optionally pre-blurred, then sharpened with range, non-linear or contrast adaptive (CAS) sharpening. The result is limited to the local minimum and maximum plus an allowed over- and undershoot, optionally softened, and can be applied only on or off edges. soothe stabilizes the sharpening over time, secure guards against banding and a waxy look. On YUV only luma is sharpened; RGB is not supported.
Settings
| Control | Parameter | Range / values | Hybrid default | Meaning |
|---|---|---|---|---|
| Defaults | defaults | old, slow, fast | fast | Preset; Apply loads its values into the fields. |
| Strength | strength | 0 – 8192 | 80 | Sharpening strength. |
| Sharpening Mode | Smode | Range sharpening, Nonlinear sharpening, Contrast Adaptive Sharpening | Contrast Adaptive Sharpening | Sharpening method. |
| Method | Smethod | 3x3 Kernel, Min/Max, Min/Max + 3x3 Kernel | Min/Max | How the blurred reference is built; only for range and non-linear mode. |
| Kernel | kernel | 11, 20, 12, 19 | 11 | Blur kernel when Method uses a kernel; 11 and 12 are the same convolution here, 19 is a ring of 8, 20 a box. |
| PreBlur | preblur | none, MinBlur(0), MinBlur(1), MinBlur(2), DFTTest | MinBlur(0) | Blur before sharpening to avoid sharpening noise. |
| secure | secure | on/off | on | Protects against banding and a waxy look; also applies in CAS mode. |
| Zero point | Szrp | 1 – 255 | 16 | Non-linear mode: zero point of the curve (8-bit units). |
| Power | Spwr | 1 – 16 | 4 | Non-linear mode: exponent of the curve. |
| Damp lo / hi | SdmpLo / SdmpHi | 0 – 255 | 4 / 48 | Non-linear mode: damping of small and large differences (8-bit units). |
| Limiting mode | Lmode | Repair(18..1), No Limit, over/undershoot, edges only, zero on edges, edges + overshoot2 on not-edges | No Limit | How the sharpened result is limited. |
| Overshoot / Undershoot | overshoot / undershoot | 0 – 81 | 0 / 0 | Allowed overshoot and undershoot (8-bit units). |
| Overshoot2 / Undershoot2 | overshoot2 / undershoot2 | 0 – 162 | twice the first values | Values for the non-edge areas; only for Limiting mode 4. |
| Soft | soft | -2 – 100 | 0 | Softening of the sharpening; -1 old auto, -2 new auto. |
| Soothe / Keep | soothe / keep | on/off, 0 – 100 | off, 20 | Temporal stabilization of the sharpening; Keep sets how much is kept. |
| Edge mode | edgemode | Show edgemask, Sharpening all, only edges, only not-edges | Sharpening all | Where sharpening is applied; Show edgemask outputs the mask. |
| HQ | edgemaskHQ | on/off | off | Better edge mask; used by Edge mode, Show edgemask and Limiting modes 2 – 4. |
| Tools: Expr | – | akarin, cranexpr, std | akarin (std without AVX2) | Expression plugin. |
| Tools: DFTTest | – | neo_fft, dfttest2cpu, dfttest2, vszipcu, vsfeel | – | DFTTest implementation for PreBlur DFTTest; GPU variants need CUDA or Vulkan. |
| Tools: RG | – | zsmooth, neo_smo | zsmooth | Repair plugin for the Repair limiting modes. |
| Tools: Median | – | zsmooth | zsmooth | Median for MinBlur(2). |
| Tools: SCD | – | scd, misc, std, mv | scd | Scene change detection for soothe; with mv the motion vector thresholds are used. |
Example
Default settings on a 10-bit YUV 4:2:0 source (640x356):
# sharpening using LimitedSharpenFaster(Mod)
clip = sharpen.LSFmod(clip, defaults="fast", tools={'expr': 'akarin', 'dfttest': 'neo_fft', 'rg': 'zsmooth', 'median': 'zsmooth', 'scd': 'scd'})How Hybrid calls it
- LSFmod works on gray and YUV clips of any bit depth; other formats are converted first.
- The preset is always written; every other value only when it differs from what the preset would set, so the script runs exactly what the controls show. Method and Kernel are left out where they do not matter, Overshoot2/Undershoot2 are only written for Limiting mode 4.
- With PreBlur DFTTest and a GPU DFTTest tool the GPU path is switched on.
- Over-/undershoot and the damp values are given on the 8-bit scale; the script scales them to the bit depth.
- Supersampling and output size are not offered; the preset values are used and the output keeps the input size.
- LSFmod also offers the common options (Masked, ApplyOnlyTo, Merge, OnRegion, Gimmick).
Background
Origin
LSFmod is LaTo's AviSynth modification of Didée's LimitedSharpenFaster; the VapourSynth version was part of havsfunc. The presets derive several values from Strength (for example the default overshoot and damping). The CAS mode uses the same plugin as CAS.
Sources
- havsfunc README
- VapoursynthScriptsInHybrid (the script collection Hybrid uses)
- Hybrid's tooltips