Vapoursynth FixFlicker
FixFlicker finds short brightness flashes – one or a few frames clearly brighter than the frames before and after – and replaces them with frames interpolated from their neighbors.
Filtering → Vapoursynth → Frame → Stabilize

What it does
FixFlicker compares the average luma of each frame with its neighbors. A frame (or a run of up to max. flash length frames) that is brighter than both sides by more than min. luma diff. counts as a flash and is rebuilt by the chosen interpolator from the frames around it. It is meant for isolated bright frames, not for slow brightness drift (use Vapoursynth Deflicker for that). A flash on the very first or last frame stays, because one side has no reference.
Requirements
- mv: CPU; the mvgpu implementation needs Vulkan.
- svp, svp_gpu: SVP must be installed (only then are they listed).
- rife: a Vulkan-capable GPU.
- gmfssfortuna (Windows only): the torch add-on with GMFSS fortuna and an NVIDIA (CUDA) GPU (only then is it listed).
Settings
| Control | Parameter | Range / values | Hybrid default | Meaning |
|---|---|---|---|---|
| Method | method | mv, svp, svp_gpu, rife, gmfssfortuna | mv | Interpolator that rebuilds the flash frames. |
| max. flash length | max_flash_frames | 1 – 10 | 1 | Longest run of frames counted as one flash. |
| min. luma diff. | min_diff | 0 – 1 (step 0.0001) | 0 | Margin, as a share of the full luma range, by which a frame must exceed its neighbors; 0 = any local maximum. |
| debug | debug | on/off | off | Shows the luma per frame and the detection in the preview. |
| RIFE: Model | – | RIFE models | rife-v4.5 (ensemble) | RIFE model (method rife). |
| RIFE: TTA / UHD | – | on/off | off / off | Test-time augmentation; UHD mode for large frames (method rife). |
| RIFE: scene thresh. | – | 0 – 1 | 0.15 | Scene change threshold for the chosen SCD tool (method rife); 0 = no scene check. Ignored with the SCD tool mv, which uses its own thresholds. |
| GMFSS: Model | – | base, union | base | GMFSS fortuna model (method gmfssfortuna). |
| GMFSS: scene thresh. | – | 0 – 1 | 0.15 | Scene change threshold (method gmfssfortuna). |
| Tools: MV | – | mvgpu, mvutensils, mv | – | MVTools implementation (method mv). |
| Tools: SCD | – | scd, misc, std, mv | scd | Scene change detection (method rife). |
Example
Default settings on a 10-bit YUV 4:2:0 source (640x356):
# removing brightness flashes
clip = FixFlicker(clip, tools={'mv': 'mvutensils', 'scd': 'scd'})
Method rife, otherwise default settings, same source:
# removing brightness flashes
clip = FixFlicker(clip, method="rife", lazy=True, tools={'mv': 'mvutensils', 'scd': 'scd'})
How Hybrid calls it
- FixFlicker works on YUV clips of any bit depth with mv, rife and gmfssfortuna; SVP converts to 8-bit 4:2:0. RGB is not accepted. min. luma diff. uses normalized luma and does not depend on the bit depth.
- Options are only written when they differ from the defaults; RIFE and GMFSS options only for their method.
- In the preview and with the method rife the detection runs per frame (lazy). With the other methods a job measures the whole clip when the script is loaded, so the encode starts only after a full pass over the source.
- Frame count and frame rate do not change.
- The interpolators: mv uses MVTools flow interpolation, svp SVP's frame interpolation, rife RIFE (ncnn/Vulkan) with optional scene detection, gmfssfortuna the GMFSS fortuna model.
Sources
- VapoursynthScriptsInHybrid (the script collection Hybrid uses)
- Hybrid's tooltips